| Author |
Message |
rubberband
Wicked Lasers Master
Joined: 13 Jan 2007
Posts: 505
Picture(s): 130
Movie(s): 12
Location: P-Tuck, connecticut
|
 Posted: 4/25/07, 12:06 AM Post subject: Diode Extr |
 |
|
has anyone ever taken out the diode of the new pulsar. i mean the little tiny thing the light comes out of. i gave taken ouy the lense and other stuff i want the diode. any suggestions?  |
|
| Back to top |
|
 |
pseudonomen137
Wicked Lasers God
Joined: 17 Mar 2006
Posts: 3680
Picture(s): 1
|
| Posted: 4/25/07, 12:13 AM Post subject: |
|
|
| You can take it out but it a bit more difficult. The only new pulsar I've dismantled had the diode soldered onto the board instead of in a little holder like the old ones so you'd have to remove that to get it off the board. |
|
| Back to top |
|
|
rubberband
Wicked Lasers Master
Joined: 13 Jan 2007
Posts: 505
Picture(s): 130
Movie(s): 12
Location: P-Tuck, connecticut
|
| Posted: 4/25/07, 12:18 AM Post subject: |
|
|
| the diode head is already seperated from the board and the pins are snaped that connected it to the board. i removed the lens and all i have now is the diode in this little head thing and i don't know how to take it out |
|
| Back to top |
|
|
chongo
Fusion Laser
Joined: 20 Dec 2006
Posts: 418
Picture(s): 9
Movie(s): 4
Location: Connecticut
|
| Posted: 4/25/07, 7:08 AM Post subject: |
|
|
| I think there press-fit into the heatsink. only way would be to try and gentlly hammer it out from the inside where the lens is, though the risk of damage will be great, as I took an axixz module apart this way and the diode did not survive. Though that's how the diode is mounted in the older black w/ clip case not sure if there still using the same basic design for the newer models. |
|
| Back to top |
|
|
BoomDog
Wicked Lasers God
Joined: 14 Dec 2005
Posts: 1704
Picture(s): 31
Movie(s): 1
Location: OH, USA
|
| Posted: 4/25/07, 8:40 AM Post subject: |
|
|
| For stuck pressfit diodes I've used a dremel before to carefully cut away the outer shell. You have to be very careful to not cut into the diode, keep it from getting too hot when cutting, and keep the optics and circuitry free of metal dust, and even then the vibrations may cause problems so it's not easy by any matter, but it works for me. |
|
| Back to top |
|
|
Aseras
Fusion Laser
Joined: 03 Nov 2006
Posts: 352
|
| Posted: 4/26/07, 8:02 AM Post subject: |
|
|
| If you are just looking to remove the diode ( like broken legs and you are going to replace) then just get a small drill bit and put a TINY hole in the back of the diode and then use a small screw and screw it in until it gets snug and slowly try to pull it out. repeat as necessary. |
|
| Back to top |
|
|
spark001uk
25mW Classic Wicked Laser
Joined: 28 Dec 2005
Posts: 29
|
| Posted: 6/11/08, 7:19 PM Post subject: |
|
|
| careful not to drill through anything else! |
|
| Back to top |
|
|
Daniel3345
25mW Classic Wicked Laser
Joined: 16 Jul 2008
Posts: 52
Location: California
|
| Posted: 8/07/08, 3:26 PM Post subject: |
|
|
| I wouldn't do that, if I were you. It will void your warranty if there is any left. |
|
| Back to top |
|
|
|
|
